How to Clean Your Car Engine

December 03, 2017
Car tools on the ground

Knowing how to clean your engine is an important part of vehicle maintenance, and it can save you money. Tidying up under the hood helps extend the life of belts, hoses and other components. Plus, it’s easier to spot leaks, tears and other damage on a clean engine. Check out the steps below to properly clean your car engine, and be sure to consult your car’s operation manual before you get started.

1. Eliminate any residue

Your car’s hood, grille and vents are prime areas for dirt buildup. Blow them out with compressed air or clean the areas with a wire hand brush.

2. Get the temperature just right

Next, let your engine warm up to a moderate temperature – not too hot. This will help soften grease buildup in the engine compartment.

3. Know what to cover when cleaning your engine

Plastic sandwich bags come in handy when it’s time to clean up your car. The parts to keep covered when cleaning your engine are:

  • Electrical wiring
  • Sensors
  • Spark plug openings
  • Alternator
  • Distributor

Secure the baggies with tape. To protect your battery, cover it or simply remove it.

4. Don’t forget the drip pan

Place old towels on an absorbent mat under the engine’s oil drip pan to catch any hazardous waste.

5. Give the engine a good spritz

Thoroughly spray the engine compartment with an engine cleaner, avoiding the wiring you bagged and taped. Since petroleum cleaners can damage rubber and vinyl components, consider a citrus or water-based degreaser. For parts that seem extremely oily or greasy, let the cleaner soak in for 15-30 minutes and repeat if necessary.

6. Rinse and unwrap

Once the engine cleaner has done its job, lightly rinse engine and components with water. Remove the bags you used to protect the wiring. Once the towel or mat is dry, dispose of it properly. And if you removed the battery, don’t forget to replace it.

7. Remove excess moisture

Blow away excess water in the engine compartment with compressed air.

8. Dry out the interior

Lastly, turn on your engine and let it run until warm. The heat will help dry the hard-to-reach areas.

Now that you know how to take care of your engine, check out our car maintenance checklist to help you keep your automobile in tip-top shape. But remember, protecting your vehicle isn’t just about regular inspections and cleaning schedules. Learn about how auto insurance works to keep you and your car safe on the road.

Knowing how to clean your engine is an important part of vehicle maintenance, and it can save you money. Tidying up under the hood helps extend the life of belts, hoses and other components. Plus, it’s easier to spot leaks, tears and other damage on a clean engine. Check out the steps below to properly clean your car engine, and be sure to consult your car’s operation manual before you get started.

  1. Eliminate any residue

    Your car’s hood, grille and vents are prime areas for dirt buildup. Blow them out with compressed air or clean the areas with a wire hand brush.

  2. Get the temperature just right

    Next, let your engine warm up to a moderate temperature – not too hot. This will help soften grease buildup in the engine compartment.

  3. Know what to cover when cleaning your engine

    Plastic sandwich bags come in handy when it’s time to clean up your car. The parts to keep covered when cleaning your engine are:
    1. Electrical wiring
    2. Sensors
    3. Spark plug openings
    4. Alternator
    5. Distributor
    Secure the baggies with tape. To protect your battery, cover it or simply remove it.

  4. Don’t forget the drip pan

    Place old towels on an absorbent mat under the engine’s oil drip pan to catch any hazardous waste.

  5. Give the engine a good spritz

    Thoroughly spray the engine compartment with an engine cleaner, avoiding the wiring you bagged and taped. Since petroleum cleaners can damage rubber and vinyl components, consider a citrus or water-based degreaser. For parts that seem extremely oily or greasy, let the cleaner soak in for 15-30 minutes and repeat if necessary.

  6. Rinse and unwrap

    Once the engine cleaner has done its job, lightly rinse engine and components with water. Remove the bags you used to protect the wiring. Once the towel or mat is dry, dispose of it properly. And if you removed the battery, don’t forget to replace it.

  7. Remove excess moisture

    Blow away excess water in the engine compartment with compressed air.

  8. Dry out the interior

    Lastly, turn on your engine and let it run until warm. The heat will help dry the hard-to-reach areas.

Category:
  • Maintenance